The Rimfire Report: Overdue SIG P322 Maintenance

Luke C.
by Luke C.
The Rimfire Report: Overdue Maintenance on the SIG P322

Hello and welcome back to another edition of The Rimfire Report! This ongoing series is about the rimfire firearm world and its many guns, ammunition types, shooting sports, and history! Last week we looked back at the Stevens Pocket Rifle (also known as the Bicycle Rifle). Although this gun might have been relatively obscure for modern firearms enthusiasts who don’t collect, it seems like the idea of the pocket rifle is one that is well received today and would probably even make for a great addition to the current rimfire firearms market was someone to take up the mantle. Some of you even reached out to me via Instagram and compared it to the Chiappa Little Badger which is a small single-shot .22LR or .22WMR rifle that basically folds in half to give the collapsed package an overall length of 17″. Many of you thought that if Chiappa simply slightly redesigned the firearm to accept a detachable brace and a slightly shorter barrel, this would be as close as we could get to the Pocket Rifle today. This week we’re dipping back into the recently released SIG Sauer P322 22LR pistol. My personal P322 is creeping pretty close to 15,000 rounds. While the gun is still running flawlessly, I think I kind of proved the point when I hit 10,000 rounds without cleaning and the gun just kept chugging along. Today we’ll be taking a look at how to field strip the P322, what the manual recommends for cleaning it, and also go a bit beyond what the manual calls for and finally take a look at some of the guts of the P322. Who’s ready for some long overdue SIG P322 maintenance?

More Rimfire Report Articles @ TFB:

The Rimfire Report: Overdue Maintenance on the SIG P322

The Rimfire Report: Overdue SIG P322 Maintenance

Just to underscore how much I think SIG underestimated their own product, the official manual for the P322 calls for cleaning and lubrication “every day the pistol is fired or at a minimum of every 500 rounds. Every 500 rounds might actually be quite a good metric for most rimfire pistols. I’ve found that my TX-22 Comp requires cleaning after about 250 rounds before I start to see a sharp uptick in malfunctions and stoppages and my Ruger MKIV seems to need cleaning and lubrication about every 1,500 to 2,000 rounds. Meanwhile, and as demonstrated before, my P322 didn’t get any cleaning or lubrication of its moving parts or friction surfaces until about 15,000 rounds (I did clean the bore of the pistol at 6,000 and 10,000 rounds). I’ve uploaded a short clip of my personally owned P322 below just before I cleaned it – just to demonstrate that it is indeed still working.

Disassembly (Field Strip)

The SIG P322 is fairly easy to field strip but somewhat counterintuitive. The P322 doesn’t break down like a normal SIG Sauer handgun. The field stripping procedure is as follows:

  1. Unload and clear the pistol
  2. Rotate the takedown lever counterclockwise 90° (left)
  3. Pull the slide back and then up to unhook it from the frame
Rotate the takedown lever 90 counterclockwise
Retract the slide fully to the rear and lift up and then forward to remove the slide from the barrel and frame

It is worth noting here that if you have the threaded barrel extension on, then you won’t be able to remove the slide from the rest of the gun. All you have to do is lock the slide back, unthread the 1/2×28 adapter and then replace it with the thread protector that the gun ships with. That’s pretty much it. Any further disassembly beyond this point is actually advised against by the manual but for reasons I’ll explain later, I decided to go further than the manual calls for.

My thread adapter is so fouled that normal scraping and brushing won't fix it. Instead, I'll have to throw it in a chemical solution to remove all the caked-on carbon

Cleaning

I gathered my regular handgun cleaning tools and got to work. The manual calls for the cleaning of the extractor, rail slots, and breech face so that they are free of dirt and residue, the barrel is cleaned with patches and a bore brush, and the frame is cleaned with CLP and cotton swabs. As you can see from the following pictures, both the slide of my P322 and its frame were quite dirty from the thousands of rounds I’ve put through it with 1/3rd of that being with a suppressor. For most of the cleaning, I simply soaked the pistols fouled parts in some Break Free CLP, and then removed all the debris with a combination of nylon brushes, patches, rags, and a dedicated scraping tool for some of the more fouled parts.

The Rimfire Report: Overdue Maintenance on the SIG P322

Section 7.4 of the SIG P322 manual gives you a step-by-step breakdown of how to field strip, clean, and reassemble the pistol. The manual also has a brief section on disassembling and cleaning the magazines but it also says this is probably not going to be necessary unless you’ve dropped the magazines in dirt or mud and that debris has somehow worked its way inside of the magazines. Regular maintenance for the 20-round magazines simply involves cleaning the magazine tube, and follower with a soft nylon brush and a cloth – this is all I did for mine.

The underside of the slide assembly is easy enough to clean with just a nylon brush, CLP, and a small flat dental scraper
I used a flat dental scraper (similar to a flathead screwdriver) to remove some more difficult spots of carbon fouling

I would have stopped here and reassembled the pistol as all the points mentioned in the manual had been taken care of. However, due to a combination of morbid curiosity, and the fact that I could hear grit and grime when working the internal hammer in and out of its cocked position, I wanted to get in deeper. If you’re going to go beyond what is stated in the manual, be sure to take note of the orientation and positioning of some of the smaller parts that will come out of the gun.

A fouled breech face can be a prime cause of stoppages and is likely where you'll see the most carbon buildup
Failures to extract can be caused by a fouled extractor. Make sure to remove debris from this area as well
Underneath the slide rails is another important spot to make sure as much debris and carbon fouling as possible is removed.

What’s Inside the SIG P322 (Further Disassembly)

The SIG P322 is somewhat reminiscent of the P320 and P365 series pistols in that its fire control group is almost all contained within one single unit that is separate from the frame itself. However, unlike the centerfire pistols, the P322 uses a mainspring housed within the grip and powered by a spring connected to a small arm that is attached to the hammer. In addition, and quite obviously, the fire control group is also attached to the barrel via a 1/8″ roll pin – for the sake of simplicity, I decided not to remove the barrel from the fire control group.

The two holes near the takedown lever and beavertail of the frame are the only roll pins that need to be removed to dislodge the fire control group

Removing the fire control group is quite simple and all that is needed is a small 4oz hammer, a bench block (or roll of tape), and a 1/8″ roll pin punch. Simply drive the two roll pins pictured above out of the gun and simply lift the fire control group/barrel assembly out of the frame of the gun taking special care not to lose the small arms that transfer spring energy from the frame into the fire control group.

The removed fire control group. Note the orientation of the small arm that transfers mainspring energy to the hammer
The orientation of this small notch is important. This connects to the left-hand side of the hammer

In order to dislodge all of the grit and grime from the fire control group, I repeated the same process of coating with CLP, removing as much as possible with cotton swabs, rags, patches, and scraping, and then recoated it with CLP and blasting the remainder of the debris from the top and out of the bottom of all the moving parts. After this, I gave the internal parts another good wipe down, cleaned out the frame which was also quite dirty, and then reassembled the pistol.

The Rimfire Report: Overdue Maintenance on the SIG P322
The Rimfire Report: Overdue Maintenance on the SIG P322
A clean breech face
The cleaned and reassembled fire control group

Conclusion

The SIG P322 continues to impress me the more rounds I put through it. I’ve been using the P322 a lot recently to introduce new shooters to the sport and go over basic pistol shooting techniques and procedures and it continues to be a reliable gun. While it may not be as easy to clean as say a Ruger MK IV, it also has (at least in my case) proven to need a lot less maintenance than other rimfire handguns and I think for new shooters this might be a good thing as it is far less intimidating to work with than older rimfire handguns.

The Rimfire Report: Overdue Maintenance on the SIG P322

Check Prices on SIG Sauer P322 Pistols

I’d like to hear what you guys think about the SIG P322 once again, specifically the interior of the handgun and how the fire control group almost mimics the P320 and P365. To me, this indicates that there might be some room down the road for SIG Sauer to adapt the P322s internals for use in both larger and smaller rimfire handguns, and perhaps even a semi-auto rifle someday. As always leave your comments below and be sure to check back again next week for another edition of The Rimfire Report!

The Rimfire Report: Overdue Maintenance on the SIG P322


We are committed to finding, researching, and recommending the best products. We earn commissions from purchases you make using the retail links in our product reviews. Learn more about how this works.
Luke C.
Luke C.

Reloader SCSA Competitor Certified Pilot Currently able to pass himself off as the second cousin twice removed of Joe Flanigan. Instagram: https://www.instagram.com/ballisticaviation/

More by Luke C.

Comments
Join the conversation
2 of 14 comments
  • American American on Nov 27, 2022

    Its not okay to let a tool get this dirty.

  • Danny Strife Danny Strife on Dec 14, 2022

    Mine ran great for close to 3K rounds before something broke and it would lite-strike every other round. Sent it back to Sig and when I got it back it had failures to feed. Sent it back again and noticed the lite-strikes were 5x more than my other rimfire pistols. Sent it back a 3rd time and it’s good for now. Have probably close to 6K rounds through it by now. I notice it prefers standard velocity ammo and the hotter you go the more it chokes; It hates heavy-grain hot stuff like Velocitor or Interceptor. However, it does fine with light-grain hot stuff like Stingers or Punch. Mine does fine with Federal AutoMatch which is great because that’s the cheapest .22 I can find. Overall, it’s great with the preferred ammo when it’s running. I prefer the TX22 Competition though, that thing is outstanding.

Next